Mastering Plumbing Fundamentals for Installing a Bathtub
Mastering Plumbing Fundamentals for Installing a Bathtub
Blog Article
Are you currently searching for know-how about How to Install a Bathtub Yourself?
Setting up a bathtub isn't exactly rocket science, however it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately difficult project. If the old tub is readily easily accessible, the job can move easily; if you need to open up a wall to remove the old tub and also place the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will require an assistant to move out the old tub and also set in the brand-new one. Make certain you have certified yourself for the work as well as fit attempting it. Rather than employing a professional to take control of a halfway-completed job, it is far better to think about employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will aid you set up a new bathtub in your washroom if you have actually currently bought a brand-new bathtub and don't need to alter the plan of your previous water pipelines.
Your devices and also product list need to make up the following:
Planning for the Setup
To start with, the sustaining frame supplied with the bath should be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic due to the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before moving on to fit the new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, place the bath tub in the needed placement. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bath tub as well as also examine the overflow electrical outlet as well as the normal outlet for leaks.
Lastly, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and also securing around the bathtub must wait up until the bath tub has been made use of at least once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Protect the tap in place with the maker supplied backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a stiff seal, causing the water to penetrate the wall surface between the bath as well as the tiling, causing complications with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and installations. They are sold in tubes and cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark down the page. We will be pleased to listen to your ideas about this post. In hopes that you visit us again in the near future. Feel free to take the opportunity to distribute this content if you enjoyed it. I value reading our article about Installing A Bathtub.
Leaks? Contact us! Report this page